Как найти устройство для чтения карт памяти?

Я пытаюсь создать образ из USB Card Reader с помощью dd, Когда я подключаю устройство, вот что говорит мне журнал:

Aug 21 11:26:50 acid kernel: [ 1399.579168] usb 1-1: New USB device found, idVendor=0451, idProduct=9260
Aug 21 11:26:50 acid kernel: [ 1399.579171] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Aug 21 11:26:50 acid kernel: [ 1399.579173] usb 1-1: Product: CU8871 CFast Card Reader
Aug 21 11:26:50 acid kernel: [ 1399.579174] usb 1-1: Manufacturer: XXX
Aug 21 11:26:50 acid kernel: [ 1399.579175] usb 1-1: SerialNumber: A69AB1E1201103290001088909A38A292
Aug 21 11:26:50 acid kernel: [ 1399.659152] scsi host9: uas
Aug 21 11:26:50 acid mtp-probe: checking bus 1, device 8: "/sys/devices/pci0000:00/0000:00:0b.0/usb1/1-1"
Aug 21 11:26:50 acid mtp-probe: bus: 1, device: 8 was not an MTP device
Aug 21 11:26:50 acid kernel: [ 1399.661589] scsi 9:0:0:0: Direct-Access     ATA      CSS HSK72W002G   0123 PQ: 0 ANSI: 6
Aug 21 11:26:50 acid kernel: [ 1399.669680] sd 9:0:0:0: Attached scsi generic sg2 type 0
Aug 21 11:26:50 acid kernel: [ 1399.673337] sd 9:0:0:0: [sdb] 3863664 512-byte logical blocks: (1.97 GB/1.84 GiB)
Aug 21 11:26:50 acid kernel: [ 1399.682743] sd 9:0:0:0: [sdb] Write Protect is off
Aug 21 11:26:50 acid kernel: [ 1399.682747] sd 9:0:0:0: [sdb] Mode Sense: 03 00 00 00
Aug 21 11:26:50 acid kernel: [ 1399.684793] sd 9:0:0:0: [sdb] No Caching mode page found
Aug 21 11:26:50 acid kernel: [ 1399.684796] sd 9:0:0:0: [sdb] Assuming drive cache: write through
Aug 21 11:27:21 acid kernel: [ 1429.864084] sd 9:0:0:0: uas_eh_abort_handler 0 uas-tag 1 inflight: CMD 
Aug 21 11:27:21 acid kernel: [ 1429.864088] sd 9:0:0:0: CDB: 
Aug 21 11:27:21 acid kernel: [ 1429.864089] Report supported operation codes: a3 0c 01 12 00 00 00 00 02 00 00 00
Aug 21 11:27:21 acid kernel: [ 1429.864107] scsi host9: uas_eh_bus_reset_handler start
Aug 21 11:27:21 acid kernel: [ 1430.132133] usb 1-1: reset high-speed USB device number 8 using ehci-pci
Aug 21 11:27:21 acid kernel: [ 1430.622732] scsi host9: uas_eh_bus_reset_handler success

Тем не менее, я не могу ничего найти с sdb в /dev, Как обозначить это устройство как блочное устройство для создания изображения?

UPD: ещё немного отладочной информации

acid@acid:~$ sudo blkid
[sudo] password for acid: 
/dev/sda1: UUID="7d39c5c7-28c5-41b5-b504-4d705380e7be" TYPE="ext4" 
/dev/sda5: UUID="9ff9235f-3c91-4ace-851b-90a2ae868c6f" TYPE="swap" 

и даже больше

acid@acid:~$ lsusb
Bus 001 Device 009: ID 0451:9260 Texas Instruments, Inc. 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 002: ID 80ee:0021 VirtualBox USB Tablet
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Больше

acid@acid:~$ lsblk
NAME   MAJ:MIN RM   SIZE RO TYPE MOUNTPOINT
sda      8:0    0     8G  0 disk 
├─sda1   8:1    0     6G  0 part /
├─sda2   8:2    0     1K  0 part 
└─sda5   8:5    0     2G  0 part [SWAP]
sr0     11:0    1  1024M  0 rom  

После нескольких раз подключения / отключения устройства я получил следующую ошибку

Error mounting /dev/sdb1 at /media/acid/3008F94408F90A1C: Command-line `mount -t "ntfs" -o "uhelper=udisks2,nodev,nosuid,uid=1000,gid=1000,dmask=0077,fmask=0177" "/dev/sdb1" "/media/acid/3008F94408F90A1C"' exited with non-zero exit status 13: ntfs_attr_pread_i: ntfs_pread failed: Input/output error
Failed to read of MFT, mft=6 count=1 br=-1: Input/output error
Failed to open inode FILE_Bitmap: Input/output error
Failed to mount '/dev/sdb1': Input/output error
NTFS is either inconsistent, or there is a hardware fault, or it's a
SoftRAID/FakeRAID hardware. In the first case run chkdsk /f on Windows
then reboot into Windows twice. The usage of the /f parameter is very
important! If the device is a SoftRAID/FakeRAID then first activate
it and mount a different device under the /dev/mapper/ directory, (e.g.
/dev/mapper/nvidia_eahaabcc1). Please see the 'dmraid' documentation
for more details.